How do you hang a closet rod from the ceiling?

Draw a straight line on the ceiling at right angles to the joists using a yardstick or straightedge tool as your guide. Make the line the length of the closet rod you purchased for the project. Put the line at least 12 inches from the back wall of the closet to allow room to hang clothes hangers on the clothes rod.

How do you hang a dowel rod from the ceiling?

Mark the ceiling or wall where you wish to hang the dowel. Drill pilot holes, using a 3/16-inch drill bit, and screw self-tapping screw eye bolts into the holes. Fasten the rope, chain or string to the eye bolts.

How do you hang a closet rod without studs?

How to Install Closet Rod in Drywall Without Studs?

  1. Step 1: Measurement or Marking Close & Walls. …
  2. Step 2: Start to Drill and Holes. …
  3. Step 3: Re-Drill for Pilot Holes. …
  4. Step 4: Position the Board. …
  5. Step 5: Transverse Center of Each Board. …
  6. Step 6: Measure the Distance Between the Screw and Finished the Process.
INTERESTING:  Is eating fish everyday healthy?

Where should closet rod brackets be placed?

Mark the position on the wall for brackets: 68″ from the floor to the top of the brackets for a single level closet, 42″ and 82″ for a bi-level closet. For safety and stability, Brackets should be spaced no more than one stud (about 32″) apart on the wall and MUST be attached directly to the wall stud.

How do you attach a dowel to the wall?

Predrill a hole in center of other end of each dowel. Using pliers, screw dowel screws into holes. If possible, mount dowels directly into studs in your wall, using level to ensure they go in straight. If not, use appropriate anchors for your type of wall, then mount dowels.

Do closet rods need studs?

Installing a closet rod in a closet without conveniently located studs is a simple job that requires no special tools or advanced carpentry skills. Closet rods are typically held by flange-type sockets that are attached to the wall, screwed into framing studs.

Do closet rods need to go into studs?

Basic Installation

It should be placed in front of a stud so you can screw into the stud to give it support. The typical height of a closet rod is from 60 to 80 inches, and both brackets should be at the same height, or the hooks you hang from the rod will slide to one end.

Can you hang closet rod with drywall anchors?

To securely install a closet rod in drywall: … Drive screws into the wall stud or drywall anchor, securing the bracket in place. Repeat this process for additional brackets, making sure they are level with the first bracket. Set your closet rod in place and use it to hang your clothing.

INTERESTING:  How many liters does a betta fish need?

How far should closet rod be from shelf?

Leave wiggle room between closet rods and shelves.

If this is the case, mount the closet rod below the shelf, achieving a distance of at least two inches from the bottom of the shelf to the top of the rod. Without this clearance, the space between the shelf and rod will be too tight to maneuver hangers.

How much space do you need between closet rods?

Standard rod height for a single closet rod is 60 inches, a height that leaves ample hanging space for floor-length dresses. When installing double rods, hang the top rod 80 inches from the floor and the bottom rod 40 inches from the floor. Leave at least 3 feet of space between the two rods.

How do you hang a closet rod in plaster?

Drill a hole through the plaster wall, insert the toggle bolt through the rod holder, press the toggle through the drilled hole and tighten it down with a screwdriver. Hang the dowel rod on the closet rod holders.

How much weight can a closet rod hold?

Aluminum Anodized Elite 1-5/16”: Up to 80 lbs. Stainless Steel 1-1/16”: Up to 95 lbs. Steel Polished Chrome Round 1-1/16”: Up to 110 lbs. Steel Polished Chrome Round 1-5/16”: Up to 170 lbs.